This study numerically investigates the long-term effectiveness of using externally bonded fiber-reinforced polymer (FRP) plates as a strengthening technique for reinforced concrete (RC) beams. A two-dimensional finite element model (FEM) that can accurately predict the flexural behavior of FRP strengthened RC beams, is developed. Weathering exposure time of 0.0, 15.5, 35, and 75 years were considered. In total, 28 different concrete beams were modelled using the developed FEM. The results show that prolonged exposure to natural weathering can cause premature FRP debonding, even before reaching the yielding load. The ultimate load capacity, midspan deflection, and ductility of strengthened RC beams can be reduced by up to 38%, 62%, and 100%, respectively. In addition, the findings raised concerns about the applicability of the ACI 440.2R-17 provisions for calculating the design flexural strength of FRP strengthened RC beams with prolonged exposure to natural weathering. To ensure a safe design for strengthened beams with FRP debonding or concrete crushing failure modes, this paper recommends an additional reduction factor ranging from 0.8 to 0.9. Furthermore, periodic inspection using non-destructive testing and FRP anchorage system are highly recommended for both existing and new applications of FRP in structures.

The use of FRP tendons has become an attractive alternative to steel tendons in prestressed concrete structures to avoid strength and serviceability problems related to corrosion of steel. There is however a lack of knowledge in serviceability behavior related to deflection after cracking for beams prestressed with FRP tendons. Conventional approaches used to compute deflection of cracked members prestressed with steel is problematic at best, and the situation is exacerbated further with the use of FRP tendons having a lower modulus of elasticity than steel. Deflection of FRP reinforced (nonprestressed) concrete flexural members computed with Branson’s effective moment of inertia 𝐼􀀁 requires a correction factor (called a softening factor) that reduces the member stiffness sufficiently to provide reasonable estimates of post-cracking deflection. For FRP prestressed concrete however, this approach does not always work as expected and deflection can be either underestimated or overestimated significantly.

This study investigates the accuracy of different models proposed for estimating deflection of cracked FRP prestressed members using a database of 38 beams collected from the literature. All beams are fully prestressed. Results indicate that using Branson’s effective moment of inertia 𝐼􀀁 with a generic softening factor can produce reasonable estimates of deflection provided the 𝐼􀀁 response is shifted up to the decompression moment or adjusted with an effective prestress moment defined by an effective eccentricity of the prestress force. The former approach overpredicts deflection by 20% on average while the latter overpredicts deflection by not more than 5% based on the beams available for comparison. Assuming a bilinear moment deflection response overpredicts deflection by 12%, while an approach proposed by Bischoff (which also shifts the 𝐼􀀁 response upwards) overpredicts deflection by 23%. These last two approaches work reasonably well without the need for a correction factor.

The current market of utility poles is growing rapidly. The dominant materials that are used for this purpose are generally wood, steel, concrete, and fiber-reinforced polymers (FRP). FRP poles are gaining wide acceptance for what they provide in terms of strength and durability, lack of maintenance and a high strength to weight ratio. Hybrid structures can combine the best properties of the materials used, where each part enhances the structure to provide a balanced structure. This study evaluates a hybrid structure composed of three main layers, an outer FRP shell, a hollow concrete core and an inner hollow steel tube, this whole system is to be utilized as a tapered utility pole. The outer FRP shell provides protection and enhances the strength of the pole, the concrete core provides stiffness, and the inner steel tube enhances the flexural performance while reducing the volume in consequence the weight of the structure compared to a fully filled pole. A new design for a 12-feet long hybrid FRP pole using finite element is presented in this paper. The design was based on a parametric study evaluating the effect of key-design parameters (i.e., the thickness of FRP, the volume and strength of the concrete, the thickness and diameter of the steel tube). Concrete strength affected the general performance of the pole, the decrease in concrete strength due to utilizing lightweight concrete was compensated with increasing the FRP pole thickness. For the same pole configuration, with incremental variation of the FRP thickness values from 3 mm to 7 mm up to the initial concrete cracking load, no significant variation of the pole top deflection was observed. However, at failure load the increase of FRP thickness from 3 mm to 7 mm decreased the ultimate tip deflection by 50%. New hybrid utility poles have the potential to be an interesting alternative solution to the conventional poles as they can provide better durability and mechanical performances.

Developments in the prestressed concrete industry evolved to incorporate innovative design materials and strategies driven towards a more sustainable and durable infrastructure. With steel corrosion being the biggest durability issue for concrete bridges, FRP tendons have been gaining acceptance in modern prestressed technologies, as bonded or unbonded reinforcement, or as part of a “hybrid” system that combines unbonded CFRP tendons and bonded steel strands. Assessments of the efficacy of hybrid-steel beams, combining bonded and unbonded steel tendons. in the construction of segmental bridges and in retrofitting damaged members has been established by several researchers. However, limited research has been conducted on comparable hybrid prestressed beams combining CFRP and steel tendons (hybrid steel-cfrp beams). This paper provides an insight on the flexural behaviour of eighteen prestressed beams tested under third-point loading until failure with the emphasis on the tendon materials (i.e., CFRP and steel) and bonding condition (i.e., bonded, unbonded). In addition, a comprehensive finite element analysis of the beams’ overall behaviour following the trussed-beam methodology is conducted and compared with the experimental results. Results show that hybrid beams, utilizing CFRP as the unbonded element maintained comparable performance when compared to hybrid steel beams. The results presented in this paper aim to expand the use of hybrid tendons and facilitate their incorporation into standard design provisions and guidelines.

The issues related to deformability, strength and ductility of concrete elements reinforced with FRP (Fiber Reinforced Polymer) bars are critically analyzed and discussed in this paper. The analysis is conducted from an experimental point of view by means of bending tests on concrete beams reinforced with Carbon FRP (CFRP) bars with different amounts of reinforcement, and by an analytical approach aiming to evaluate the deflection and cracking phenomenon (number and width of cracks). The experimental results are compared with the analytical predictions and with predictions developed on the basis of the available codes (ACI, EC2, JSCE). The analysis of the results obtained confirms the most relevant issues of the mechanical behavior of FRP bar-reinforced beams, still worthy of research efforts; some technological and construction solutions that can provide significant improvements are also addressed.