International Concrete Abstracts Portal

The reduction in the shear capacity using recycled coarse aggregate made from crushed concrete is evaluated in terms of tensile cracking and fracture surface characteristics. An experimental investigation is presented into the fracture and flexure-shear behaviors of recycled aggregate concrete (RAC). Replacing natural aggregate in concrete proportioned for 30 MPa compressive strength with recycled coarse aggregate results in lower compressive and tensile strengths. The tensile fracture surface characteristics vary between RAC and natural aggregate concrete (NAC). While the surface area created in the tensile fracture of RAC is larger than that of NAC, the fracture surface profile in RAC has a smaller roughness than that of NAC. In the flexure-shear response of reinforced concrete beams, the dilatancy determined from the slip and crack opening displacements measured across the shear crack is smaller in RAC than NAC. The failure in the reinforced beam is due to the frictional stress transfer loss across the primary shear crack. There is a larger decrease in the shear capacity with the use of RAC than indicated by the reduction in compressive strength. The reduced shear capacity of reinforced RAC is due to the combined influences of reduced tensile strength and crack surface roughness. The design provisions require calibration for crack surface roughness when using RAC in structural applications.

Engineered cementitious composites (ECC), a prominent innovation in the realm of concrete materials in recent years, contain a substantial amount of cement in their composition, thereby resulting in a significant environmental impact. To enhance the environmental sustainability of ECC, it is plausible to substitute a large portion of cement in the composition with fly ash, a by-product of coal-fired power plants. In recent years, there has been increased research in ECC containing high-volume fly ash (HVFA) binders and its wider application in construction practices. In this particular context, it becomes imperative to review the role of the HVFA binder in ECC. This review first examines the effects of incorporating an HVFA binder in ECC on fiber dispersion and fiber/matrix interface behavior. Additionally, mechanical properties, including the compressive strength, tensile behavior, and cracking behavior under loading, as well as durability performances of HVFA-based ECC under various exposure conditions, are explored. At last, the review summarizes the research needs pertaining to HVFA-based ECC, providing valuable guidance for future endeavors in this field.

Reinforced concrete walls are commonly used in low- and mid-rise construction because they provide high strength, stiffness, and durability. In regions of low and moderate seismicity, ACI 318 Code requirements for minimum reinforcement ratio and maximum reinforcement spacing typically control over strength-based requirements. However, these requirements are not well-supported by research. The current study investigates requirements for the amount and spacing of reinforcement using experimentally validated nonlinear finite element modeling. For lightly reinforced concrete walls subjected to out-of-plane loading: 1) peak strength is controlled by concrete cracking; and 2) residual strength depends on the number of curtains of steel. Walls with very low steel-fiber dosages were also studied. Results show that fiber, rather than discrete bars, provides the most benefit to wall strength, with fiber-reinforced concrete walls achieving peak strengths more than twice that of identically reinforced concrete walls.

This paper presents experimental testing results on full-scale reinforced concrete (RC) column specimens subjected to quasi-static cyclic loading. Two types of lap-spliced steel reinforcing bars were used: hot-rolled thermomechanically treated (TMT) and coldtwisted ribbed bars. The specimens were tested under varying axial load levels: CD-10 and CD-20 specimens, reinforced with TMT bars, were loaded at 10% and 20% of the column’s axial load capacity, respectively, while the CT-20 specimen, reinforced with cold-twisted ribbed bars, was axially loaded at 20% capacity. In contrast to the cold-twisted bars, the TMT bars’ yield strength exceeded the specified strength by 38%, leading to an underestimation of the required reinforcing bar splice length and significantly impacting cracking patterns and curvature near the dowel end. The CD-20 and CT-20 specimens showed comparable lateral load capacity and initial stiffness, substantially higher than the CD-10 specimen. The CT-20 specimen exhibited symmetrical hysteretic behavior, indicating a consistent response to reversed cyclic loading, with (on average) 10% and 45% higher peak and ultimate displacement capacity than CD-10 and CD-20, respectively, and 45% higher displacement ductility capacity. Notably, only the CT-20 specimen met the acceptance criteria for structural testing described by the code of practice, while the lower ductility and ultimate rotation capacity of CD-10 and CD-20 resulted from the unintended increase in reinforcing bar yield strength.

Linear structural analysis is the method of choice commonly used by practicing engineers to support the seismic design of a structure. The structural models are developed in commercial software and incorporate stiffness modifiers, which lower the stiffness of the members, in recognition of all the sources of flexibility that occur upon cracking of the concrete. This paper describes a mechanics-based model to compute the stiffness modifiers for columns with a circular cross-section. The mechanics-based model accounts for five modes of deformation observed. Calibration of this model was performed with a database of tests reported in the literature on twenty-two circular-section columns that exhibited ductile response. The paper ends by describing a simplified method for use in design. The mechanics-based model and the design method yield an effective column lateral stiffness that closely aligns with the values obtained from the column database.