his paper presents preliminary experimental and numerical results of a research program aimed at investigating the residual capacity of 60-year-old reinforced concrete bridge girders strengthened using CFRP sheets. Two 4.5 m and 5.0 m long, bridge girders were deconstructed from a bridge located in Canada. The two 60-year-old girders have been strengthened with CFRP for the last six years of the service life of the bridge. The two full-scale girders were tested at the structural lab of Sherbrooke’s University after having suffered under real service conditions. A finite element model using the ANSYS program had been validated with the experimental results before it was used as a control sample for non-strengthened conditions. The test results revealed that the CFRP strengthening technique can extend the service life of the bridge element by keeping their shear capacity safe. The CFRP strengthening configuration of the two girders increased the maximum shear capacity by 35.5 % and 30 % over the finite element control model. The presented outcomes show the effectiveness of using the external CFRP sheets as an external technique for bridge rehabilitation. The test results were compared with the ACI 440 2R-17 and CSA S6-19 design guidelines. The theoretical comparison between guidelines, experimental and numerical results shows that the two guidelines are considered overly conservative.

The manuscripts included herein introduce common learning theories and methods in engineering education that can be specifically applied to the topics of reinforced concrete and concrete materials. The papers focus on the application of these theories to specific concrete-related topics and suggest ways to implement these methods in university classrooms. The primary goal of this Special Publication is to provide pedagogical resources, ideas, and techniques that can be implemented by anyone that accepts the challenge of teaching reinforced concrete and concrete materials, from a new instructor to an experienced professor. To disseminate effective teaching methods among a global group of educators and learners, ACI Committee S802 organized two sessions entitled “Best Practices and Lessons Learned for Teaching Concrete Materials and Reinforced Concrete” at the Spring 2021 ACI Virtual Convention. The first session was focused on best practices teaching concrete materials and the second session was focused on best practices teaching introductory reinforced concrete. The manuscripts in this Special Publication are organized in the order in which they were presented at the ACI Convention. The co-editors, Dr. Benjamin Dymond and Dr. J. Chris Carroll, are grateful for the contributions from the Special Publication authors and sincerely value the time and effort of the authors in preparing the papers in this volume. Furthermore, the Special Publication would not have been possible without the effort expended by the experts who peer reviewed the papers in this volume.

The Canada Centre for Mineral and Energy Technology (CANMET) of Natural Resources of Canada, Ottawa, ON, Canada, has played a significant role for more than 40 years in the broad area of concrete technology in Canada. In recent years, CANMET has become increasingly involved in research and development dealing with supplementary cemen¬titious materials, high-performance normalweight and lightweight concretes, and alkali-aggregate reactions. As part of CANMET’s technology transfer program, an international symposium on Advances in Concrete Technology was sponsored jointly with the American Concrete Institute (ACI) and other organizations in Athens, Greece, in May 1992. In June 1995, CANMET, in association with ACI and other organizations in Canada and the United Staes, sponsored the Second CANMET/ACI Symposium on Advances in Concrete Technology in Las Vegas, NV, USA. For the Athens symposium, the CANMET publication “Advances in Concrete Technology,” constituted the proceedings of the symposium. The proceedings from the Las Vegas symposium were published by ACI as SP-154. In August 1997, CANMET, in association with ACI and other organizations in Canada and New Zealand, sponsored the Third CANMET/ACI Symposium on Advances in Concrete Technology in Auckland, New Zealand. The main purpose of the symposium was to bring together representatives from industry, universities, and government agencies to present the latest information on concrete technology, and to explore new areas of research and development. Thirty-three refereed papers from 15 countries were presented and distributed at the symposium. The proceedings were published as ACI SP-171. In June 1998, CANMET, in association with ACI, Japan Concrete Institute (JCI), and several other organizations in Canada and Japan, sponsored the Fourth CANMET/ACI Conference on Recent Advances in Concrete Technology in Tokushima, Japan. More than 80 papers from 20 countries were received and reviewed in accordance with the policies of ACI. Sixty-one refereed papers were accepted for presentation at the conference and for publication as ACI SP-179. In addition to the refereed papers, more than 30 papers were presented and distributed at the conference. In July-August 2001, CANMET, in association with ACI and several organizations in Singapore, sponsored the Fifth CANMET/ACI Conference on Recent Advances in Concrete Technology in Singapore. More than 100 papers from 25 countries were received and reviewed in accordance with the policies of ACI. Forty-six refereed and more than 25 additional papers were accepted for presentation at the conference. The proceedings of the conference were published as ACI SP-200. In June 2003, CANMET, in association with ACI and several organizations in Romania, sponsored the Sixth CANMET/ACI Conference on Recent Advances in Concrete Technology in Bucharest, Romania. More than 40 papers presented at the conference were distributed “as received,” and no formal ACI special publication was published. In May 2004, CANMET, in association with ACI and several other organizations in the United States, sponsored the Seventh CANMET/ACI Conference on Recent Advances in Concrete Technology in Las Vegas, NV. Seventeen refereed papers from more than 10 countries were presented and distributed at the conference. The proceedings of the conference, consisting of the refereed papers, were published as ACI SP-222. In addition to the refereed papers, 20 additional papers were presented and distributed at the conference. In May 2006, CANMET, in association with ACI and several other organizations in Canada and the United States, sponsored the Eighth CANMET/ACI Conference on Recent Advances in Concrete Technology in Montreal, QC, Canada. The proceedings of the conference, consisting of 17 refereed papers, were published as ACI SP-235. In addition to the refereed papers, more than 30 additional papers were presented and distributed at the conference. In May 2007, CANMET, in association with ACI and several other organizations in Canada, Europe, and the United States, sponsored the Ninth CANMET/ACI Conference on Recent Advances in Concrete Technology in Warsaw, Poland. The proceedings of the conference, consisting of 10 refereed papers, were published as ACI SP-243. More than 20 additional papers were presented and distributed at the conference. In October 2009, ACI, in association with several organizations in Canada, Europe and the United States, sponsored the Tenth ACI Conference on Advances in Concrete Technology in Seville, Spain. The proceedings of the conference, consisting of 20 refereed papers, were published as ACI SP-261. In addition to the refereed papers, more than 20 additional papers were presented at the conference and published in a supplementary papers volume. In May 2010, the Committee for the Organization of International Conferences (COIC) (formerly CANMET/ACI Conferences), in association with the Chinese Ceramics Society (CCS) and several other organizations in China, sponsored the Eleventh International Conference on Advances in Concrete Technology and Sustainability Issues in Jinan, China. More than 40 papers were presented at the conference. The proceedings of the conference were published by the CCS, Beijing, China. In October 2012, the COIC, in association with ACI, sponsored the Twelfth International Conference on Advances in Concrete Technology and Sustainability Issues in Prague, Czech Republic. The proceedings of the conference, consisting of more than 30 refereed papers, were published as ACI SP-288. In addition to the refereed papers, more than 40 other papers were presented at the conference and published in a supple¬mentary papers volume. In July 2015, the COIC, in association with ACI, sponsored the Thirteenth International Conference on Advances in Concrete Technology and Sustainability Issues in Ottawa, ON, Canada. The proceedings of the conference, consisting of 28 refereed papers, were published by ACI as SP-303. In addition to the refereed papers, more than 40 other papers were presented at the conference and published in a supplementary papers volume. In October 2018, the CCS and the China Academy of Building Research (CABR), Beijing China, in association with the COIC sponsored the Fourteenth International Conference on Recent Advances in Concrete Technology and Sustainable Issues in Beijing, China. The proceedings of the conference, consisting of 19 refereed papers, were published by ACI as SP-330. In addition to the refereed papers, more than 52 other papers were presented at the conference and published in a supplementary papers volume. In July 2022, after a postponement for the Covid-19 pandemic, the ACI Italy Chapter and the University of Bergamo, Italy, sponsored the Fifteenth International Conference on Recent Advances in Concrete Technology and Sustainable Issues in Milan, Italy. The proceedings of the conference, consisting of 44 refereed papers, were published by ACI as SP-355. In addition to the refereed papers, about 20 other papers were presented at the conference and published in a supplementary papers volume. The main topics of the papers presented at the conference include: the deterioration of concrete structures; the corrosion of metallic reinforcement; the repair techniques of damaged concrete structures by using shrinkage-compensating cement-based mixtures; the protection of concrete structures by special materials to obtain watertight concrete; the reduction of the damage caused by alkali-silica reaction; the use of mineral additions such as fly ash, silica fume, and ground-granulated blast-furnace slag to improve the durability of concrete structures; and the production of concrete by reducing gas emissions and energy consumption such as the use of binders alternative to portland cement (alkali activated materials, geopolymers, sulphoaluminate cement) and recycling of wastes coming from different sources. Thanks are extended to the reviewers for the valuable efforts in reviewing all the manuscripts published in the conference proceedings and in the supplementary volume. The guidance from Dr. V. M. Malhotra and Prof. M. Collepardi, the Honorary Chairpersons of the conference, is sincerely appreciated. Also, acknowledged is the support the American Concrete Institute for the publication of the proceedings (ACI SP-355). The Editors Dr. Denny Coffetti Prof. Luigi Coppola Dr. Terence Holland

In May 1978, the Canada Centre for Mineral and Energy Technology (CANMET), in association with the American Concrete Institute (ACI) sponsored a 3-day conference in Ottawa, ON, Canada, on the use of superplasticizers in concrete. Selected papers from the conference were published as ACI SP-62. In 1981, CANMET, again in association with ACI, sponsored a second 3-day international conference in Ottawa on the use of the superplasticizers in concrete. Proceedings of the conference were published as ACI SP-68. The purpose of the third international conference in Ottawa in 1989 was to review the progress made since the meetings in 1978 and 1981, and to bring together representatives of the chemical admixtures, cement, and concrete industries to exchange information and delineate new areas of needed research. The scope of this conference was expanded to include chemical admixtures other than superplasticizers. Proceedings of the conference were published as ACI SP-119. In October 1994, CANMET in association with ACI and several other organizations sponsored the fourth conference in Montreal, QC, Canada. The objective of this conference was to bring attention to new developments in chemical admixture since the last conference in 1989. The proceedings of the conference were published as ACI SP-148. In October 1997, the Committee for the Organization of CANMET/ACI International Conference, (ACI Council), in association with ACI and several cement and concrete organizations in Italy, sponsored the fifth conference in Rome, Italy. The conference was aimed at transferring technology in the fast-moving field of chemical admixtures. The proceedings of the conference were published as ACI SP-173. In October 2000, Committee for the Organization of CANMET/ACI International Conferences, (ACI Council), in association with several organizations in Canada and France, sponsored the sixth conference in Nice, France. More than 50 papers from more than 20 countries were received and reviewed by an ACI review panel, and 37 were accepted for publication in the proceedings of the conference. The proceedings were published as ACI SP-195. In October 2003, the Committee for the Organization of CANMET/ACI International Conferences (ACI Council) in association with several organizations in Canada and Germany, sponsored the seventh conference in Berlin, Germany. The conference attracted more than 275 delegates and proceedings of the conference consisting of 39 papers, were published as ACI SP-217. In October 2006, the Committee for the Organization of CANMET/ACI International Conferences, (ACI Council), sponsored the eighth conference in Sorrento, Italy. More than 60 papers from more than 25 countries were received, and peer reviewed by the CANMET/ACI review panel in Budapest, and 36 were accepted for publication as ACI SP-239. In October 2009, the Committee for the Organization of International Conferences (COIC) (formerly CANMET/ACI International Conferences) sponsored the ninth ACI International Conference in Seville, Spain. More than 50 papers from more than 20 countries were received and peer reviewed, and 35 were accepted for publication in the proceedings of the conference. The proceedings were published as ACI SP-262. In October 2012, COIC sponsored the Tenth International Conference on Superplasticizers and Other Chemical Admixtures in Concrete in Prague, Czech Republic. More than 70 papers from all over the world were peer reviewed, and 33 were accepted for publication in the proceedings of the conference. The proceedings were published as ACI SP-288. In July, 2015, the COIC in association with ACI sponsored the Eleventh International Conference on Superplasticizers and Other Chemical Admixtures in concrete in Ottawa, ON, Canada. More than 60 papers from the world over were peer reviewed, and 28 were accepted for publication in the proceedings of the conference. Also, additional papers were presented at the conference that were published in the Supplementary Papers Volume. In October 2018, the Chinese Ceramic Society and the China Academy of Building Research (CABR), Beijing China, in association with ACI, sponsored the Twelfth International Conference on Superplasticizers and other Chemical Admixtures in Concrete in Beijing China. More than 80 papers from all over the world were received and peer reviewed. A total of 36 refereed papers were accepted for publication in the proceedings of the conference. The proceedings were published by as ACI SP-329. The proceedings were published as ACI SP-302. Also, 54 additional papers were presented at the conference, and were published in the Supplementary Papers Volume. In July, 2022, after a postponement for the COVID-19 pandemic, the ACI Italy Chapter and the University of Bergamo, Italy, sponsored the Thirteenth International Conference on Superplasticizers and Other Chemical Admixtures in Concrete in Milan, Italy. The proceedings of the conference consisting of 35 refereed papers were published by ACI as SP-354. In addition to the refereed papers, about 20 other papers were presented at the conference, and were published in a supplementary papers volume. The main topics of the papers presented at the conference are related to superplasticizers, accelerating admixtures, retarding admixtures, air-entraining agents, shrinkage-reducing agents, superabsorbent polymers, and self-healing admixtures, and their influence on the properties of the concrete in fresh and hardened state. These properties include: workability, slump-loss, time of setting, heat of hydration, strength, durability, shrinkage, and creep of the concrete mixtures. Thanks are extended to the reviewers for the valuable efforts in reviewing all the manuscripts published in the conference proceedings and in the supplementary volume. The guidance from Dr. V. M. Malhotra and Prof. M. Collepardi, the Honorary Chairpersons of the conference, is sincerely appreciated. Also, acknowledged is the support of ACI International for the publication of the proceedings (ACI SP-354). The Editors Dr. Denny Coffetti Prof. Luigi Coppola Dr. Terence Holland

The purpose of this symposium and special publication is to recognize and honor Professor Amin Ghali’s outstanding long-term dedication to the concrete industry. Dr. Ghali obtained his B.Sc. and M.Sc. degrees in Civil Engineering from Cairo University, Cairo, Egypt, respectively in 1950 and 1954, his Ph.D. from Leeds University, England in 1957. He spent ten years in engineering practice before joining at the University of Calgary, AB, Canada as a professor in 1966. Dr. Ghali has developed the revolutionary, multi-patented and globally used, headed-stud shear reinforcement systems for concrete flat slabs; he has been a consultant for a number of major international structures, including offshore structures, multi-story buildings, bridges, and tanks. Dr. Ghali authored over 300 papers and eight patents. In 15 editions and 6 translations, his books include: Structural Analysis Fundamentals (2022), Structural Analysis: A Unified Classical and Matrix Approach (2017), Circular Storage Tanks and Silos (2014), and Concrete Structures: Stresses and Deformations (2012). Professor Ghali has served the industry in many ways, including his role as a voting member of ACI Committee 435, Deflection of Concrete Building Structures, 343, Concrete Bridge Design, and 421, Design of Reinforced Concrete Slabs. Jointly with associates at University of Calgary, his research on punching shear design and control of long-term deflection enables design of affordable concrete floors. Dr. Ghali served as expert, providing technical testimony, for a number of complicated engineering cases. Dr. Ghali received a number of teaching and research excellence awards over his long career, and was elected a Fellow of ACI, ASCE, CSCE, and CAE; in 2017, he received the Top 7 Over 70 Award for his outstanding continued research and engineering contributions. The papers found in this SP publication encompass a broad overview on the important issues related to punching shear resistance and sustainable serviceability of flat plates from both a theoretical and design perspectives. These papers formed the basis of presentations made at the Amin Ghali Symposium on Design of Structural Concrete Slabs for Safety Against Punching and Excessive Deflection held at the ACI Fall 2020 Virtual Convention, on October 25, 2020. Twelve presentations were made in two sessions by those who have worked closely with Dr. Ghali in his areas of interest. The SP includes nine papers on design of concrete floors for punching and for serviceability. The sessions were sponsored by ACI Committee 421, Design of Reinforced Concrete Slabs. All papers in this publication were reviewed by at least two recognized experts in accordance with ACI review procedures. Special thanks are extended to all who helped to make the two technical sessions and accompanying publication a success.