Adhesive Anchor Installer

Certification Programs

Adhesive Anchor Installer


Find a Testing / Training Location Near You:


Country/Region

State/Province


Definition:


An Adhesive Anchor Installer is an individual who has demonstrated the ability to read, comprehend, and execute instructions to properly install adhesive anchors in concrete. The Adhesive Anchor Installer must also demonstrate possession of the knowledge to properly assess ambient conditions, concrete condition, materials, equipment, and tools for installing adhesive anchors and determine when it is appropriate to proceed with installation of an adhesive anchor or when additional guidance from a supervisor/foreman/project engineer is needed.


Scope and Knowledge:

This program requires knowledge and ability in the following areas of adhesive anchor installation:

  • Understanding jobsite conditions relevant for correct selection of installation procedures in accordance with manufacturer’s instructions (e.g. concrete wetness, hole drilling method used, possible embedded obstructions, and air and concrete temperature)
  • Understanding the manufacturer’s instructions (pictograms, text) and using the proper procedures, sequence, and tools to clean the hole
  • Proper selection and assembly of the injection equipment
  • Awareness of the potential impact of storage conditions and verification of the expiration date on the cartridge
  • Rejection of the initial adhesive expressed from new cartridges as applicable and proper procedures followed for disposal of rejected/waste adhesive/used nozzles and cartridges
  • Injection of adhesive into holes at various orientations to the proper depth using proper technique and equipment that minimizes air voids
  • Correct assembly of anchor element in drill chuck and drill settings for capsule anchor installation
  • Recognition of time limits for installation and positioning of anchor element (i.e., gel time) depending on type of adhesive, ambient conditions, and size/depth of anchor hole
  • Installation of the anchor element in accordance with manufacturer’s instructions
  • Knowledge of proper measures for protection of anchor element threads from adhesive
  • Knowledge of measures to secure and protect the anchor element from load/movement during adhesive cure


Job Task Analysis (JTA) for ACI Adhesive Anchor Installer Certification


Certification Requirements:

ACI will grant certification only to those applicants who obtain a passing grade on both the written examination and performance examinations.

  1. The 90-minute written examination is closed-book and consists of 75 multiple-choice questions.
  2. The performance examination consists of two parts, Part 1 (vertical down) and Part 2 (vertical up):
    • In Part 1, each examinee will be tasked with selecting, assembling, and using the proper tools, equipment and materials to drill and clean a vertical down hole in concrete, inject adhesive, and set an anchor to the proper depth and perpendicularity. The Examiner(s) will observe and evaluate the examinees’ performance for proper procedure.
    • In Part 2, each examinee is required to inject clear tubes with adhesive in a vertical up orientation behind a blind to simulate a drilled hole in concrete; one tube is injected using the retaining cap method, and one tube is injected using the piston plug method. The Examiner(s) will observe and evaluate the examinees’ performance for proper procedure.

Following Part 1, the Examiner(s) will check the vertical down installation for proper depth and plumb; after the adhesive in the tubes injected in Part 2 has cured, the Examiner(s) will cross section them and evaluate the size and location of air voids to determine pass or fail. This program now certifies candidates in either OR both of the "overhead" installation systems (retaining-cap and piston-plug).

A set of instructions appropriate for the exam along with applicable Material Safety Data Sheets (MSDS) will be available for consultation by the examinee during both parts of the performance exam. Both parts of the performance must be successfully completed within one year or the entire performance examination must be re-taken.

Recertification is necessary every five years and requires successful completion of both the written and performance examinations.


Study Material:

Go to the ACI Bookstore on this website to order and/or obtain current pricing on any items listed below:

CP-80 PACK: Installer Workbook for ACI Adhesive Anchor Installer with Companion DVD

This workbook provides educational information on adhesive anchors and their installation methods, as well as examination procedures & criteria for the ACI Adhesive Anchor Installer certification program. A companion DVD detailing the installation methods and certification procedures is also included.

CP-80SPACK: Adhesive Anchor Installer Workbook with Companion DVD Spanish

The Spanish workbook provides the same educational information on adhesive anchors and their installation methods, as well as examination procedures and criteria for the ACI Adhesive Anchor Installer certification program as the English 2012 edition. A companion DVD detailing the installation methods and certification procedures in both Spanish and English is also included.

eLearning: Adhesive Anchor Installer Certification Training: 1 Course