ACI Home Page
About ACIAbout ACI Bookstore & PublicationsACI Publications CertificationACI Certification ChaptersACI Chapters CommitteesACI Committees Conventions & EventsACI Events EducationACI Education InternationalInternational MembershipACI Members StudentsACI Students TechnicalTechnical
 
 
   

 
   

ACI FRC Bowling Ball Competition

REGISTRATION FORMS:
Part 1: Online Advance Registration Form - CLOSED
Part 2: Official Registration Form - CLOSED

Commonly Asked Questions

2008 FRC Bowling Ball Competition Winners

2006 FRC Bowling Ball Competition Winners

2004 FRC Bowling Ball Competition Winners

2002 FRC Bowling Ball Competition Winners

Objective

The objective of this competition is to demonstrate the effect of fibers in reinforcing concrete, to gain experience in forming and fabricating a concrete element, and to encourage creativity in engineering design and analysis.

Prizes

Prizes will be awarded in two (2) categories, a) Performance and b) Prediction. First, Second, and Third Prizes will be awarded in each category to the teams as defined in the rules. The awardees will each receive a certificate of recognition. Further recognition will be from ACI’s website and Concrete International magazine, if space allows. The First Place team will receive a $300 award, the Second Place team will receive $200, and the Third Place team will receive $100.

Rules   Back to top   

1. The Challenge

  1. To design and construct a fiber-reinforced concrete bowling ball to achieve optimal performance under specified failure criteria.
  2. To develop a fabrication process that produces a radial uniform density while maximizing volume.

2. The Student Team

  1. Each team must have a supervising faculty advisor who will see that the student team complies with the rules of the competition.  The faculty member is permitted to advise more than one team.
  2. A team is limited to five students currently enrolled in a high school or undergraduate program. Undergraduate students on cooperative or internship work assignment are eligible to compete. All members of a given team must be from the same school. A student may not be a member of more than one team.
  3. It is strongly recommended that at least one individual (faculty advisor or student team member) be designated to represent each team and be present during the testing of specimens at the time and location specified for this competition.
  4. Each team must submit registration forms Part 1 and Part 2 above. Only the first two completed advance registrations will be accepted from one school.  Additional teams will only be accepted if an earlier entry from the same school withdraws from the competition. ACI encourages schools to hold local competitions to select the teams that will represent them at this international competition.

3. Materials and Curing

  1. The bowling ball must use cementitious materials as binder. The cementitious materials shall be Portland cement meeting ASTM C 150, blended cement meeting ASTM C 595, or expansive cement meeting ASTM C 845. Supplementary cementitious materials such as fly ash and natural pozzolan meeting ASTM C 618, silica fume meeting ASTM C 1240, and slag meeting ASTM C 989 may also be used.
  2. Any type of non-metallic aggregate may be used.
  3. Chemical admixtures meeting ASTM C 494 or ASTM C 1017 may be used. Glues and similar binders, such as epoxies and other polymers, are not allowed.
  4. Curing shall be at atmospheric pressure. The curing temperatures shall not exceed the boiling point of water. Use of a standard moist curing room is permitted.
  5. The fiber-reinforced concrete mixture design shall include fibers of maximum 60 mm length and made of steel, glass, synthetic or natural materials as described in ACI 544.1R. The fibers may be used at any dosage rate. No other type of reinforcing is allowed.
  6. Filling of honeycombed surfaces after casting is allowed. Fill materials must be selected from the same materials used in the original concrete mixture.

    .

4. Specimen 

  1. The bowling ball mass shall not exceed 5.5 kg. The bowling ball shall measure 215 mm +/- 15 mm diameter.
  2. The bowling ball shall be cast or formed monolithically. A ball consisting of smaller precast units bonded together by any means will be disqualified.
  3. The bowling ball may be solid (homogeneous) or core filled. If core filled, the maximum density of the filler material shall be no greater than 2400 kg/m3.
  4. The bowling ball cannot be cast prior to Feb 29, 2008.
  5. Modification of entries shall not be permitted once they are submitted for the competition. 

5. Qualification and Testing Procedures

The competition procedures consist of three steps, all handled by a group of judges appointed by the Chair of ACI-E 801.

  1. Qualification for further Testing
    2. Each team must have two balls for competition and only one sealed envelope with their school and team name or similar acronym. The balls are marked with the team name or similar acronym with suffix #1 and #2 for identifying each of the two balls. A judge will arbitrarily choose ball #1 or ball #2 for submission to the competition. The team will submit the chosen ball and envelope to the judge. The team will keep the ball not chosen available for the judge until the competition is closed. The judges will minimally handle the balls. The ball will be handled primarily by one person from each team throughout the competition. The bowling ball submitted will be individually checked for compliance to the requirements of Sections 2 through 4 of these rules. Only after the qualification for further testing has been completed, will each qualifying bowling ball be submitted to the Roll Test and Load Test.
  2. Roll Test
    3. The bowling ball will be positioned at the top of a V-shaped ramp and propelled down the ramp by the force of gravity onto a flat surfaced lane. (See diagram below) As shown below in the illustration, the ramp shall be 1,220 mm long and raised 400 mm on one end in order to achieve a reasonable ball speed. The ball must “strike” between two edges spaced 600 mm apart at the end of the 3,000 mm long lane. Each ball shall be rolled in two orientations as arbitrarily marked “mostly perpendicular” on the ball by the judges. For each orientation, each ball will be given two tries to successfully pass through the strike zone.
  3. Load Test
    4. The bowling ball will next be placed in a testing apparatus. The load shall be applied with the initial speed of the crosshead displacement set at 10 mm/min. Load will be applied until the crosshead displacement of the testing apparatus has traveled 25 mm. The load will be recorded at this point. In addition, the load will be recorded at every 5 mm of crosshead displacement and the average of the five loads will be computed, which will be used for final score evaluation (see Section 6). 

6. Test Evaluation

Performance Prize Category
The scoring equation -

Final Performance Score = Average Load x (Diameter) x Roll Test Multiplier

  1. The diameter is taken as an average of two orthogonal measurements “mostly perpendicular” and chosen by the judge.
  2. To compute the roll test multiplier, deduct 10% in the final score for each failed roll out of the four rolls attempted during the roll test. Thus, a ball with one failed run would have a 0.90 multiplier for the final score. The lowest deduction would then be 0.60.
  3. The team that achieves a Final Score with the highest value will receive the prize for first place. The teams with the next highest values in descending order will receive the prize for second and third place. In the case of a tie, the winner is determined based on largest test load.
  4. If a bowling ball fails to reach a deflection of 25 mm prior to reaching the test apparatus' capacity, the load test will be stopped and the loads associated with any remaining crosshead displacements will be recorded as the capacity of the test machine.

Prediction Prize Category
The scoring equation–

Final Prediction Score = abs. value [ 1 – {Predicted (envelope value) / Actual (measured value)} ]

The Predicted and Actual loads are at 25 mm deflection. The team that achieves a Final Score with the lowest value will receive the prize for first place. The teams with the next lowest values in descending order will receive the prize for second and third place. In the case of a tie, the winner is determined based on higher performance score.

7. Judging

  1. The competition and presiding judge will be appointed by the Chair of Committee E 801 and sub-committee chair from Committee 544 - Education. This judge will appoint other judges from ACI Committee 544 Fiber Reinforced Concrete.
  2. The judges will determine whether or not the rules have been followed.
  3. The decision of the judges will be final, and appeals will not be considered.

8. Submitting the Bowling Ball Entries and Supporting Materials

  1. Submitting the Bowling Ball Entries and Supporting Materials
  2. Advance Online Registration is required. The Online Advance Registration Form (Part 1) must be submitted no later than March 7, 2008.
  3. The bowling balls accompanied by the Official Registration Form (Part 2) must be submitted in person along with the specimen and sealed Prediction envelope no later than 11:00 a.m. on the day of the competition. 

9. Compliance with ACI-Bowling Ball Competition Rules

CI reserves the right to perform detailed examination and check entries for compliance with the competition rules. Examination will also be done after the competition. If examination shows that a team did not follow the rules, the team, their advisor and teams from the same school will be disqualified. ACI Committee E 801 will further document recommendations to sanction the team, their advisor, and/or school/university participation in future competitions.

10. Contact Information

For technical inquiries:

Vivek Bindiganavile, PhD
FRC Bowling Ball Competition Chair
E-mail: vivek@ualberta.ca

For question regarding registration:

Lacey Jones
American Concrete Institute
E-mail: students@concrete.org